motorcycle repair
 
 
 
 
motorcycle repair and troubleshooting

Home Repair Tips
- Vehicle Repair -
 
 
 
Motorcycle Repair Directory
 
   Tires
   Brakes
   Chain
Motorcycle Repair
- 2007 - 2008 -
Yamaha Motorcycles
Suzuki Motorcyles
Kawasaki Motorcycles
Honda Motorcycles
BMW Motorcycles
Ducati Motorcycles
Triumph Motorcycles
Custom Search
Search Motorcyle Repair
Flywheel removal for 2002 & 2003 Yamaha R1. Need to remove flywheel for stator replacement. Common problem on 02/03 R1's. Usually stators on these bikes go out every 20-25,000 miles. Use for informational purposes only, I assume no risk or liability for damages that occur while doing this repair. Do at your own risk.

Parts: www.yamahasportscenter.com (Best Deal IMO on yamaha OEM parts)

Tools: Evercraft 5 ton 3-jaw Puller Part #: 775-3908
Custom Search
Search Motorcyle Repair
motorcycle-repair
motorcycle-repair
Yamaha R1 Stator
Each motorbike owner have to take it as their own responsibility to get informed of the basic parts to ensure that it performs optimally. If you are not previously aware about CDI ignition and motorcycle stator, then you might find the details on different parts a little too overwhelming to grasp. Ensure that you read further below to obtain details on the function for each and how they can improve your motorcycle's performance.

CDI Ignition

CDI, or Capacitor Discharge, Ignition is one of several automotive electronic ignition systems that are often used for powering small engines, cars, turbine-powered aircraft, and motorcycles. It was built in order to address the lengthy charging periods that were very common with high inductance coils. It first emerged into the automotive industry way back in the 1980s.















Motorcycle Charging System

Motorcycles need to use a battery to be able to store electric energy that will be utilized for several reasons and also to help the motor to keep running. You should charge the batteries before using it in order that it can perform as it is made for. Ideally, it ought to be charged at 14.4 Vdc in order to generate adequate voltage at specific engine speeds.


There are currently two standard systems used for charging motorcycle batteries. The first system is referred to as Permanent Magnet Generator System that utilizes a winded coper on the motorcycle stator that is responsible for generating power. Meanwhile, the second system is called Field Controlled Generator System. This one performs almost like a permanent magnet generator but without using magnet, rather it relies upon an electromagnet to create that magnetic field. This is similar to a car's charging system.

Motorcycle Stator

The stator is a stationary section of the motorcycle's alternator, which is often complex for novices to comprehend it is therefore vital that you take a look at the standard electrical system used on a motorbike. This is a fundamental component for any vehicle as it is accountable for storing electric charge that is to be utilized in order for it to operate. Your motorcycle need the alternator to create AC which will enable the ignition systems, halogen bulbs, and tail lights to turn on. Given that the battery is not capable of storing the AC itself, you should convert the energy first into DC in order that it can be stored.

You can find several motorcycle stator designs to choose from but they usually have a similar basic principle. Running a magnet past a coil allows the coil to produce a burst of electricity. The length and amount of winding components to a stator varies based on the power requirements for your motorcycle and ensure maximum power output on your vehicle.

Now you may use this information on CDI ignition and aftermarket motorcycle parts, particularly if you need to invest on a replacement for such motorcycle components. If you are still not sure, you can always consult a professional in order to get advice on making the most suitable purchase.

Monica C. Cohen
Monica C. Cohen writes about
aftermarket motorcycle parts and accessories. If you are looking to get a new CDI ignition or motorcycle stator for your motorbike, make sure to read her articles so you can get tips on how to go about this process.
CDI Ignition

CDI, or Capacitor Discharge, Ignition is one of several automotive electronic ignition systems that are often used for powering small engines, cars, turbine-powered aircraft, and motorcycles. It was built in order to address the lengthy charging periods that were very common with high inductance coils. It first emerged into the automotive industry way back in the 1980s.

When utilized on vehicles and motorcycles, the essential principle in the utilization of a CDI ignition depends on electric induction from the coil to produce electricity which is capable of bursting the spark plug. Most CDI modules are made up of a tiny transformer, triggering circuit, charging circuit, and main capacitor. CDI systems differ in terms of the amount of energy it can store, which is typically around 50 mJ or more.

Motorcycle Charging System
Beginners' Guide To CDI Ignition And Other Motorcycle Parts
When utilized on vehicles and motorcycles, the essential principle in the utilization of a CDI ignition depends on electric induction from the coil to produce electricity which is capable of bursting the spark plug. Most CDI modules are made up of a tiny transformer, triggering circuit, charging circuit, and main capacitor. CDI systems differ in terms of the amount of energy it can store, which is typically around 50 mJ or more.